Garage door service for San Marcos homes built 1984-2014. We know the springs, openers, and hardware that fail first in this housing stock and mild climate.
Most of the houses we get called to sit in the 1984-2014 build window, with a median around 1996. That's not a coincidence of who's calling - it's most of the housing stock across the sixteen communities we cover, from Redwood and Martindale in close to Kyle, and out toward Lockhart and Seguin. A door installed when a house was framed is now somewhere between 10 and 40 years old, and torsion springs, nylon rollers, and drivetrain gears all have a working life measured in cycles, not years. When a neighborhood goes up in a five or ten year stretch, the doors in it tend to fail in a five or ten year stretch too, just offset by however long the original hardware lasted. We see clusters of the same call - same spring gauge, same worn plastic idler pulley, same stripped gear - because the houses around them were built the same year by the same production builder. That pattern is why we ask when your house was built before we ask what the door is doing.
What Causes It Around Here
The climate here is mild with occasional freeze, which sounds easy on hardware and mostly is - no deep freeze-thaw cycling to crack concrete or seize galvanized coils the way a harder winter would. But mild-with-freeze cuts both ways: grease formulated for warm weather thickens on the handful of nights that dip below freezing, and a torsion spring that's been running dry all summer suddenly has more resistance right when a cold snap hits it. Combine that with 1980s-90s builder-grade hardware, which is what's actually hanging in a lot of these garages, and you get springs and cables sized to a minimum standard, not a generous one. Add a few decades of Texas heat swelling wood jambs and door panels, and the tracks that were bolted true when the house was new are rarely still square. None of this is dramatic. It's slow wear, showing up on a schedule tied to when the neighborhood was built, not to any one bad storm.
How It Shows Up
It usually starts small. The door hesitates a half-second before it moves, or the opener motor runs a beat longer than it used to before the door actually lifts. Some owners hear a rhythmic thump from a flat spot worn into an old roller; others notice the door hangs slightly crooked at the bottom, one corner lower than the other, which is track wear or a spring losing tension unevenly. On the older end of that 1984-2014 range, we still find the original spring on doors that have never been serviced - and those tend to fail all at once, not gradually, with a bang and a door that won't budge. On newer builds near the 2010s end, the more common call is an opener gear or capacitor giving out, since that hardware has a shorter design life than the springs it's paired with.
What the Repair Takes
A straightforward spring or roller job is usually a same-visit repair once we're on site - we carry stock sizes that cover most of what shipped in this area's housing boom. Where it takes longer is custom or oversized doors, or hardware from a builder that used a spring size we don't carry on the truck; those need an order, and we'll tell you that up front rather than promise a same-day fix we can't back. We won't sell a full opener replacement when a $30 gear kit solves it, and we won't patch a track that's bent badly enough to keep coming back - past a certain point, straightening it costs more in return visits than replacing the section. If your door is original to a house built in the 1990s and has never had the springs serviced, plan on that being the conversation, because at that age it's due regardless of what brought us out.
How it works
From “it’s stuck” to “it’s fixed”
01
Tell us what’s wrong
Describe the symptom - won’t open, loud bang, opener runs but the door won’t move.
02
On-site diagnosis
A technician tests the door under power and by hand and finds what actually failed.
03
Clear, up-front plan
You get the fix that’s needed and what drives the cost - before any work starts.
04
Repaired & tested
The repair is done, the door is set true and tested, and the work area left clean.
Serving San Marcos, TX - tell us what your door’s doing and we’ll take it from there.
How old does a garage door have to be before the springs need attention?
Torsion springs are rated in cycles, not years, but on a typical once-or-twice-daily door that works out to roughly 7-15 years. Since most San Marcos-area houses were built between 1984 and 2014, a large share of the original hardware in this area is now past or approaching that mark, which is why spring calls cluster by neighborhood age.
Does the occasional freeze here actually hurt garage doors?
Not the way a hard winter would, but it matters. Grease that's fine all summer stiffens on the coldest nights, adding resistance right when older, dry hardware is already working harder than it should. It's rarely the sole cause of a failure, but it's often what tips a worn spring or roller over the edge.
Can you match the hardware on a builder-grade door from the 1990s?
Most of it, yes - that era used a narrow range of spring and track sizes and we stock the common ones. Some production-builder doors used a less common size, and those need to be ordered, which we'll flag before starting the job rather than after.
Ready to get your garage door sorted?
Tell us what it’s doing and where you are in San Marcos - we’ll take it from there.
